Nederlands
Engels
Bezoek HERMEQ Irlande
Bezoek HERMEQ Frankrijk
Bezoek HERMEQ DuitslandBouwplaats Poorten
Gerelateerde producten
The Construction Site Gate is a heavy-duty in-ground gate that offers access to vehicles. Manufactured with welded mesh wire infill these gates are supplied with dig-in posts and adjustable eye-bolts to connect the gate leafs directly to the posts. Available in various colours, heights and sizes.
Snelst mogelijke bezorgtijd: Snelst mogelijke bezorgtijd: Tot 5 werkdagen
Our Construction Site Gates are most commonly used on building and construction sites, fitting perfectly alongside either a steel or timber hoarding system. These heavy-duty gates are very easy to install. The gate posts for the construction site gates sit 600mm in-ground (the gate posts can be made to 1000mm if required) and are easily connected to the gate leaf frames using a simple eyebolt system. This adjustable eyebolt system allows you to amend the height of the gate leafs to fit the contour of the ground.
Many people prefer a mesh construction site gate over a gate with a solid steel infill for a number of reasons. Firstly, they are considerably lighter, making the installation of the gates by hand much simpler. Secondly, being able to see through the mesh construction site gate is preferable from a health and safety aspect, as you can see what is on either side of the gate when opening and closing it.
Our gates come in a range of sizes to fit your needs. Most commonly, they are 2.0m high to fit alongside steel or low height timber hoarding, or 2.4m high to fit alongside the majority of timber hoarding. We also offer them in various widths, with the most popular being 5.0m wide, as it allows for two lanes of traffic comfortably. Larger gates of 6.0m and 7.0m widths are recommended for particularly active construction sites with a constant stream of large vehicles passing through them.
We can paint or powder coat these construction site gates to suit your requirements. So, if you don't see the finish you would like for your gates, just email us at sales@hermeq.nl/nl or call 0800 043 2520. Most construction and building sites opt for painted gates (one-side) based on a price point. However, painting does not provide a perfect finish and this can result in running and/or chipping. Powder coating is a much superior finish and is suggested for situations where aesthetics are important.
It is important when installing these gates to allow the posts to set. The most common way to install the gates is to install the posts, connect the gate leafs, and then leave these gate leafs in a fixed position, with some form of support under them taking the weight. They should remain supported in a fixed position until the gates have set. Removing this support before the posts are ready will cause them to lean.
HERMEQ stock a wide-range of Temporary Mesh Fencing, Acoustic Barriers, Tree Protection Fencing & Accessories conforming to all required safety specifications and regulations.
Heb je nog hulp nodig? Neem dan contact op met HERMEQ.
Neem contact op door te e-mailen naar sales@hermeq.nl of bel ons tussen 9:00 en 17:00 op +31 202417011
Frames are made up of 60 x 40 x 2.0mm Hot Rolled Square Hollow Section.
Posts are made up of 100 x 100 x 4.0mm Hot Rolled Square Hollow Section.
The vehicle gate posts sit 600mm in-ground, subsequently they are 600mm longer than the size of the vehicle gate e.g. a 2.4 meter high vehicle gate will come with 3.0 meter vehicle gate posts.
The posts and vehicle gate frame are connected using an eyebolt system.
All of our heavy duty construction site vehicle gates come with a slide bolt allowing you to secure them shut and maximise site security.
Size: Our construction site vehicle gates are available in a range of sizes including 2.0 & 2.4 meter heights and 4, 5 & 6 meter widths.
Finish: Vehicle gates are normally painted (one-side). However we can have these painted or powder coated to suit your requirements, so if you do not see the option you would like please get in touch with a member of our team.
